Extraction of petroleum
From Wikipedia, the free encyclopedia
The extraction of petroleum is the process by which usable petroleum is extracted and removed from the earth.
Contents |
[edit] Locating the oil field
Nowadays, geologists use seismic surveys to search for geological structures that may form oil reservoirs. The "classic" method includes making underground explosion nearby and observing the seismic response that provides information about the geological structures under the ground [2]. However, "passive" methods that extract information from naturally-occurring seismic waves are also known [1].
Other instruments such as gravimeters and magnetometers are also sometimes used in the search for petroleum. When extracting crude oil, it normally starts by drilling wells into the underground reservoir. When an oil well has been tapped, a geologist (known on the rig as the "mudlogger") will note its presence. Historically, in the USA, some oil fields existed where the oil rose naturally to the surface, but most of these fields have long since been used up, except certain places in Alaska. Often many wells (called multilateral wells) are drilled into the same reservoir, to ensure that the extraction rate will be economically viable. Also, some wells (secondary wells) may be used to pump water, steam, acids or various gas mixtures into the reservoir to raise or maintain the reservoir pressure, and so maintain an economic extraction rate.
[edit] Oil extraction and recovery
[edit] Primary recovery
During the primary recovery stage, reservoir drive comes from a number of natural mechanisms. These include: natural water displacing oil upward into the well, expansion of the natural gas at the top of the reservoir, expansion of gas initially dissolved in the crude oil, and gravity drainage resulting from the movement of oil within the reservoir from the upper to the lower parts where the wells are located. Recovery factor during the primary recovery stage is typically 5-15%.[2]
While the underground pressure in the oil reservoir is sufficient to force the oil to the surface, all that is necessary is to place a complex arrangement of valves (the Christmas tree) on the well head to connect the well to a pipeline network for storage and processing.
[edit] Secondary recovery
Over the lifetime of the well the pressure will fall, and at some point there will be insufficient underground pressure to force the oil to the surface. After natural reservoir drive diminishes, secondary recovery methods are applied. They rely on the supply of external energy into the reservoir in the form of injecting fluids to increase reservoir pressure, hence replacing or increasing the natural reservoir drive with an artificial drive. Sometimes pumps, such as beam pumps and electrical submersible pumps (ESPs), are used to bring the oil to the surface. Other secondary recovery techniques increase the reservoir's pressure by water injection, natural gas reinjection and gas lift, which injects air, carbon dioxide or some other gas into the reservoir. Typical recovery factor from water-flood operations is about 30%, depending on the properties of oil and the characteristics of the reservoir rock. On average, the recovery factor after primary and secondary oil recovery operations is between 30 and 50%.[2]
[edit] Tertiary recovery
Tertiary oil recovery reduces the oil's viscosity to increase oil production. Thermally enhanced oil recovery methods (TEOR) are tertiary recovery techniques that heat the oil and make it easier to extract. Steam injection is the most common form of TEOR, and is often done with a cogeneration plant. In this type of cogeneration plant, a gas turbine is used to generate electricity and the waste heat is used to produce steam, which is then injected into the reservoir. This form of recovery is used extensively to increase oil production in the San Joaquin Valley, which has very heavy oil, yet accounts for 10% of the United States' oil production.[citation needed] In-situ burning is another form of TEOR, but instead of steam, some of the oil is burned to heat the surrounding oil. Occasionally, detergents are also used to decrease oil viscosity as a tertiary oil recovery method.
Another method to reduce viscosity is carbon dioxide flooding.
Tertiary recovery allows another 5% to 15% of the reservoir's oil to be recovered.[3]
Tertiary recovery begins when secondary oil recovery isn't enough to continue adequate production, but only when the oil can still be extracted profitably. This depends on the cost of the extraction method and the current price of crude oil. When prices are high, previously unprofitable wells are brought back into production and when they are low, production is curtailed.
[edit] Recovery rates
The amount of oil that is recoverable is determined by a number of factors including the permeability of the rocks, the strength of natural drives (the gas present, pressure from adjacent water or gravity), and the viscosity of the oil. When the reservoir rocks are "tight" such as shale, oil generally cannot flow through but when they are permeable such as in sandstone, oil flows freely. The flow of oil is often helped by natural pressures surrounding the reservoir rocks including natural gas that may be dissolved in the oil (see Gas oil ratio), natural gas present above the oil, water below the oil and the strength of gravity. Oils tend to span a large range of viscosity from liquids as light as gasoline to heavy as tar. The lightest forms tend to result in higher production rates.
[edit] Drilling
The oil well is created by drilling a hole into the earth with an oil rig. A steel pipe (casing) is placed in the hole, to provide structural integrity to the newly drilled wellbore. Holes are then made in the base of the well to enable oil to pass into the bore. Finally a collection of valves called a "Christmas Tree" is fitted to the top, the valves regulating pressures and controlling flows.
[edit] See also
- Oil well
- Drilling rig
- Drilling fluid
- Mud logger
- Roughneck
- Directional drilling
- Oil platform
- Driller (oil)
- Deep well drilling
- Blowout (well drilling)
- Oil Megaprojects
[edit] References
- ^ A technology web site of a passive - seismic based company [1]
- ^ a b E. Tzimas,. "Enhanced Oil Recovery using Carbon Dioxide in the European Energy System" (PDF). European Commission Joint Research Center. Retrieved on 2008-08-23.
- ^ Green, D W (2003). Enhanced Oil Recovery. Society of Petroleum Engineers. ISBN 978-1555630775.
|
||||||||||||||||||||||||||||||||
| Rozmowy przedstawicieli Gazpromu i Naftohazu |
|
W nocy ze środy na czwartek doszło w Moskwie do spotkania szefów rosyjskiego Gazpromu i ukraińskiej firmy Naftohaz - ujawniła rano agencja ITAR-TASS.
|
| Zablokowany wjazd na obwodnicę Torunia |
|
Zablokowana jest droga krajowa nr 10 przy wjeździe na obwodnicę Torunia w Lubiczu, gdzie w czwartek rano zderzyły się cztery samochody. Jedna osoba została ranna.
|
| TIR wpadł w poślizg - zginęła jedna osoba |
|
Do wypadku dwóch TIR-ów doszło w środę wieczorem na drodze krajowej nr 2 siedem kilometrów od Świecka (Lubuskie). Na miejscu zginął pasażer jednego z pojazdów - poinformował oficer dyżurny lubuskiej policji.
|
| Odciążą Augustów kosztem innej miejscowości? |
|
Generalna Dyrekcja Dróg Krajowych i Autostrad w Białymstoku chciałaby odciążyć Augustów i skierować część ruchu tirów na drogę biegnącą przez miejscowość Raczki, czytamy w "Naszym Dzienniku".
|
| USA: Powodzie na północnym zachodzie |
|
Groźne powodzie wystąpiły w środę w położonym na północnym zachodzie USA stanie Waszyngton. W rezultacie szybkiego przyboru wód w rzekach zalane zostały znaczne obszary. Władze wezwały tysiące osób do opuszczenia ich domów.
|